NEC PD17062 Manuale Utente Pagina 157
- Pagina / 296
- Indice
- SEGNALIBRI
Valutato. / 5. Basato su recensioni clienti
157
µ
PD17062
13.4.2 Halt Release Conditions
Fig. 13-3 summarizes the release conditions.
As shown in Fig. 13-3, the halt release condition is 4-bit data specified in the operand h of the HALT h
instruction.
The halt state is released when a condition specified as 1 in the operand h is satisfied.
Upon release of the halt state, the subsequent instructions after the HALT h instruction are executed
sequentially.
If multiple release conditions are specified at a time, the halt state is released when only one of them is
satisfied.
Also when a power-on or CE reset occurs, the halt state is released and the device is reset.
If the operand h is 0000B, no halt release condition is specified.
Under this condition, the halt state is released by resetting (power-on or CE reset) the device.
Sections 13.4.3 to 13.4.6 explain the timer carry FF, interrupt, and key entry as halt release conditions.
Fig. 13-3 Halt Release Conditions
b
3
b
2
b
1
b
0
0
1
HALT h (4 bits)
Operand bits
Specify a condition to release the halt state.
The halt state is released by a high level applied to a key entry pin (P0D
3
/ADC
5
to P0D
0
/ADC
2
pins).
The halt state is released when the timer carry FF is set to 1.
Undefined (to be fixed at 0)
The halt state is released when an interrupt (INT
NC
pin, timer, V
SYNC
, serial interface) is accepted.
The halt state is not released even when the condition is satisfied.
The halt state is released when the condition is satisfied.
- MOS INTEGRATED CIRCUIT 1
- ORDERING INFORMATION 2
- FUNCTION OVERVIEW 2
- PIN CONFIGURATION (TOP VIEW) 3
- PD17062GC-×××-3BE 4
- BLOCK DIAGRAM 5
- 1. PINS 11
- RESET signal (except for P1C) 14
- A/D Converter 15
- High on-state 15
- P0B3/HSCNT 16
- P0B2/TMIN 16
- (Hysteresis input) 17
- 2. PROGRAM MEMORY (ROM) 18
- 3. PROGRAM COUNTER (PC) 25
- 4. STACK 26
- DD is applied 28
- 5. DATA MEMORY (RAM) 29
- R, (r)) ← (m) 42
- Row address 43
- Discrimi 50
- R and mC 51
- 8. SYSTEM REGISTER (SYSREG) 54
- 2-b0, 7BH b3), of 57
- Comparison 59
- Transfer 59
- Example 1. ADD03H,11H 61
- Specifies the source 61
- 0 b3 b2 b1 b0 66
- 9. REGISTER FILE (RF) 67
- Peripheral hardware 70
- StackTimerInterrupt 70
- C bus method 72
- (only for 2-wire method) 72
- 2) (SPb0) 75
- 9.3 CE (07H, b0) 76
- NC pin and VSYNC pin 80
- 0 INTNC pin 87
- 1 Clock timer 87
- 2 VSYNC pin 87
- 3 Serial interface 87
- 10. DATA BUFFER (DBF) 88
- 0 to bit6.) 95
- Peripheral 100
- 11. INTERRUPT 106
- BANK PSW 107
- NC pin) 108
- NC pin) can be selected 108
- Serial interface 01H 109
- INTNC pin 04H 109
- Timer 03H 109
- VSYNC pin 02H 109
- NC pin), each type of 111
- NC pin) is used 114
- (a) Hardware priorities 115
- (b) Software priorities 115
- 0 of the 116
- 3 b2 b1 b0 b3 b2 b1 b0 121
- SYNC pin 121
- Active edges of interrupt 122
- SYNC pinINTNC pin 122
- System register restoration 131
- Interrupt permission 131
- 12. TIMER 133
- 2/TMIN pin 134
- 2/TMIN pin by 5 or 6 134
- CHECK < tSET 138
- SET < error < tCHECK 140
- CHECK + tTIMER < tSET 142
- Interrupt pending 149
- Input latch 153
- DD is turned on 155
- 0 at address 07H) 155
- 14. RESET 171
- Reset signal 173
- (b) At clock-stop 179
- (c) When VDD rises from 0 V 179
- During this period 182
- DD is dropped 183
- DD or by the CE pin, as 184
- DD is turned on, they 184
- Operation stopped 185
- 15. GENERAL-PURPOSE PORT 189
- 3 b2 b1 b0 191
- Note Nothing is mapped to b 193
- 3, P0A2 pins) 194
- 3, P0B2, P0B1, P0B0 pins) 194
- 3, P1B2, P1B1, P1B0 pins) 194
- 3, P1C2, P1C1 pins) 194
- 1, P0A0 pins) 194
- At reset 195
- 3, P0D2, P0D1, P0D0 pins) 198
- 3, P0C2, P0C1, P0C0 pins) 199
- 3, P1A2, P1A1, P1A0 pins) 199
- 16. SERIAL INTERFACE 201
- Remark × : Don’t care 202
- Remark ×: Don’t care 203
- 3 is used as an SO pin 205
- 1/SCL pin for 206
- Bit position b3 b2 b1 b0 207
- 6789123456789 208
- SCL, SCK 208
- Bit counter 208
- Flag name SBACK SIO0NWT 209
- SIO0WRQ1 SIO0WRQ0 209
- 17. D/A CONVERTER 217
- 6 b5 b4 b3 b2 b1 b0 218
- 3 b2 b0b1 223
- N” of the 226
- (2) When fN is leading fr 227
- (4) When fN is lower than fr 227
- Upon reset 229
- (PLLUL flag = 1) 230
- 19. A/D CONVERTER 233
- REF = VDD × 234
- DD = 5 V 234
- Flowchart 238
- 20. IMAGE DISPLAY CONTROLLER 240
- Blank (black) 241
- Background (TV screen) 241
- Sample program 244
- 01 234 5 6789AB 249
- 800001 400 249
- ID field Data field 250
- VRAM column address 250
- 7 b6 b5 b4 b3 b2 b1 b0 252
- 0 BANK0 0800H-0BFFH 255
- 1 BANK1 0C00H-0F7FH 255
- 14 and b13 of control data) 258
- 10 corresponding 259
- 10 to b7 of the control data) 259
- 6 to b3 of the control data) 260
- 6 corresponding 260
- 2 to b0 of the control data) 261
- 7 b6 b5 b4 b3 b2 b1 b0 264
- 3 b2 b1 b0 b3 b2 b1 b0 264
- IDC image area 265
- SYNC and 267
- SYNC signals supplied to the 267
- SYNC signal that comes 267
- 20.8 SAMPLE PROGRAMS 268
- 269
- 22. INSTRUCTION SETS 277
- The reserved 282
- 23.1 SYSTEM REGISTER 282
- 23.2 DATA BUFFER 282
- 23.3 PORT REGISTER 283
- 23.4 REGISTER FILES 284
- NC interrupt request flag 285
- 23.6 OTHERS 286
- 64 PIN PLASTIC QFP ( 14) 290
- SMD Surface Mount 291
- Technology Manual 291
- APPENDIX DEVELOPMENT TOOLS 292
- Cautions on CMOS Devices 295
- M4 94.11 296
Prodotti e manuali riguardandi no NEC PD17062
no NEC NP-U321H-WK Disegni e schemi
(1 pagine)
(1 pagine)
no NEC X841UHD Disegni e schemi
(1 pagine)
(1 pagine)
no NEC E905-AVT Disegni e schemi
(1 pagine)
(1 pagine)
no NEC PD Comms Tool Guida Utente
(62 pagine)
(62 pagine)
no NEC V652-DRD Disegni e schemi
(1 pagine)
(1 pagine)
no NEC P242W-BK-SV Disegni e schemi
(2 pagine)
(2 pagine)
no NEC E585 Disegni e schemi
(1 pagine)
(1 pagine)
no NEC Express5800/R120f-1M Manuale Utente
(54 pagine)
(54 pagine)
no NEC E321 Disegni e schemi
(1 pagine)
(1 pagine)
no NEC V462-AVT Manuale di Installazione
(2 pagine)
(2 pagine)
no NEC E321 Disegni e schemi
(1 pagine)
(1 pagine)
no NEC Express 5800/320Fd Manuale Utente
(26 pagine)
(26 pagine)
no NEC E552 Disegni e schemi
(1 pagine)
(1 pagine)
no NEC V462 Disegni e schemi
(1 pagine)
(1 pagine)
no NEC E655 Disegni e schemi
(1 pagine)
no NEC X474HB Disegni e schemi
(1 pagine)
(1 pagine)
no NEC Express5800/R110f-1E Guida Utente
(122 pagine)
(122 pagine)
no NEC LCD4620-2-AV Disegni e schemi
(1 pagine)
(1 pagine)
(6 pagine)
no NEC X461UNV Disegni e schemi
(1 pagine)
© 2020, manymanuals.it. Tutti i diritti riservati | 0.103 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commenti su questo manuale